Exterior Finishing: Vinyl / PVC
"F" Series Architectural Soffit Vent
AFCS Series of one-piece soffit vent with a reinforcing rib to key into stucco
3/4" elongated vent holes.
"F" Series Control Joint and Vent
Designed to work on narrow overhangs
Where vents are needed to go against fascia or walls.
Architectural Soffit Vent
Series of one-piece soffit vent with a reinforcing rib to key into stucco
3/4" elongated vent holes.
EIFS/DEFS Corner Bead
Designed for use in EIFS and DEFS wall and ceiling systems
These corner beads are hard to damage, rust-proof, and straight.
FCS Soffit Vent
Available in several grounds and widths
Can be ordered with the 300VFZ clip for installation.
Miscellaneous Soffit Vent
One-piece Soffit Vent designed for plywood, soffit board, and three-coat stucco
May be combined with Starter Strips / Casing Beads or DEFS Casing Beads.
Soffit Drip - Pre-Installed
Designed for exterior soffits where a drip screed and edge reveal need to be combined
Pre-installed soffit edge reveals with a drip edge to direct moisture away from the installation.
Soffit Drip - Surface Mount
Designed for exterior soffits where a drip screed and an edge reveal need to be combined
Used to direct moisutre away from the installation in EIFS and DEFS installations. Always use a rigid backing or blocking material behind surface…
Soffit Vent Control Joint Combination
Continuous, one-piece, combination design like a control joint
Allowing movement of the plaster with a vent area that has a perforated flange to assist with embedment.
Soffit Vent with J-Flange
J-bead flanges cover the raw edges of soffit board
One-piece soffit vents provide an economical means for venting soffit areas. Vent clips are provided for proper connection and alignment of the soffit vents.
Soffit Vent with Perforated Flanges
Provides an economical means for venting soffit areas
One-piece soffit vent with perforated flanges to assist in embedment of the base coat mixture and to cover the raw edges of the soffit board. Vent clips are provided for proper…
Soffit Vents (One-Piece with Edge Clip)
Continuous one-piece Soffit Vent
Reinforcing rib to key into stucco and plaster. Vertical edge clips are provided for special installations.
Soffit Vents (One-Piece)
Continuous one-piece Soffit Vent
Reinforcing rib to key into stucco and plaster with a perforated flange.
Soffit Vents (Three-Piece with Edge Clip)
Continuous three-piece Soffit Vent
For stucco and plaster.
Soffit Vents (Two-Piece Narrow Overhang)
Continuous two-piece Soffit Vent
For stucco and plaster with vertical edge clips provided for special installations.
Surface Mount Soffit Vent
One-piece soffit board designed for venting soffit areas over exterior board in EIFS and DEFS applications
Available with 2", 3", 4" wide vents, each with a 1/8” ground. Vent clips are provided to connect the soffit vent and to assist in…
Vented Channel Reveal - Surface Mount
Vented Channel Reveals facilitate perimeter air flow to assist in moisture management and temperature control
This vent is intended for surface-mount applications. Always use a rigid backing or blocking material behind surface-mounted…
Vented Drip Screed
Designed to address finishing the plaster to the vertical soffit area intersection
When a drip and soffit vent need to be combined.
Vented Shadow Reveal
Designed for ceilings when a vented reveal is required at the juncture of a wall and ceiling where horizontal movement may occur
Vent clips are provided to connect reveal sections and to assist in their alignment.
Vinyl 3-1/2" Drip Screed w/ Weep Holes and Tape